Вы здесь

/
/
/
AD-120 on KAMAZ 43253

AD-120 on KAMAZ 43253

Smoke exhaust vehicles (AD)
Request a call

Горизонтальные вкладки

Specifications
Short description: 

An AD-fire smoke is intended for transportation of smoke and/or rescue unit (ASF) personnel, respiratory and vision protective equipment firefighting equipment and rescue tools and equipment , preparation on a site of fire, accidents, emergency control post of Gas and Smoke Protection Service, lighting, providing electricity electricity on the site of fire, accident, emergency portable electrical-power tools, Induced-draft fans, spotlights and other electric equipment required for fire-fighting and rescue operations.

The advantages of this model: 
  • It can operateat a temperature from minus 40 to plus 40° c,  at an atmosphere of  1 and 2 types as per GOST 15150
  • The engine and transmission provide allow the vehicle to work in a nominal a mode during 6:00
  • Te rollover threshold with a total mass in full operational availability is at least 30 degrees
  • Angle of approach: Front-20"; Rear -15"
  • Pneumatic dual circuit braking system with a division of the contours into the front axle and rear truck, with anti-lock braking system
  • The batteries are protected from dirt and moisture
  • The fuel tank capacity allows operating for 6 hours from primary power source at nominal load without refuelling
  • The exhaust system is equipped with a spark arrestor
  • There is an additional fuel filter with a water separator
  • The driver's cabin and the crew cabin represent common space, constitute a single sealed structure
  • The cabin design saves space if the car is overturned, or in case of head-on collision, rear-end accidents and sideways.
  • The equipment in the cabin is positioned in such a way that there are no sharp corners and edges
  • The design of the mast allows its operation without stretching at wind speed up to 10 mps.
  • The mast is equipped with a mechanism of orientation (rotary device), spotlights  with remote drive in two planes
  • A high-resolution video registrator  (Full HD)  1280 * 720, 30 fps is available, viewing angle width of 110 degrees, no pauses between blocks, sound recording available;
  • Sensor pixel count- 2 MP

General characteristics

Basic characteristics

Wheel formula: 
4x2 - 4x4
Chassis brand: 
KamAZ
Combat crew, people: 
2 – 8
General characteristics: 
Full weight, kg 10 400 – 14 500
Length, mm 7 200 – 8 000
Height, mm 2 900 – 3 300
Width, mm 2550

More

* Manufacturing according to special customer requirements. The site does not contain the entire product line. Send us an application for a proposal
Make a request
Equipment
Short description: 

An AD-fire smoke is intended for transportation of smoke and/or rescue unit (ASF) personnel, respiratory and vision protective equipment firefighting equipment and rescue tools and equipment , preparation on a site of fire, accidents, emergency control post of Gas and Smoke Protection Service, lighting, providing electricity electricity on the site of fire, accident, emergency portable electrical-power tools, Induced-draft fans, spotlights and other electric equipment required for fire-fighting and rescue operations.

Notes on equipment: 

1- Fixed generator for 3-phase current distribution, chassis-driven. Power at least 16 kW. Voltage 230-400 v, frequency renge-not less than 50 Hz.
2- Portable electric generator with protective cutout device. Operating capacity at least 6kW. Tank capacity not less than 6.5 l
3- Handheld starter. Activity time not less than 2.5 hours.
4- A reel with the main cable of 100 m length, protection degree not less than IP 76
5- Portable cable reel of at least 40 m length, protection degree at least IP 76
6- Power switchboard
7- Protective cutout device GOST R 51326.1-99
8- Branch box 220-3B0V on support, 3 directionsbr /> 9- Branch box 220-3B0V on support, 3 directions
10- Motor-driven induced-draft fan , with a capacity of not less than 20 000 m3/h, the maximum angle of declination not less than 20 degrees, engine power of not less than 18.0 hp., the duration of battery life at a maximum speed of at least 1.5 h, dimensions ( length/width/height) not more 625/725/785 mm, dry weight 83 kg, with attack hose of length not less than 5 m. 1 pcs.: foam generator adapter-1 pcs.
11- Motor-driven induced-draft fan , with a capacity of not less than 15 000 m3/h, the maximum angle of declination not less than 20 degrees, voltage 220 V, dimensions (length/width/height) not more 520/570/550 mm, dry weight no more than 45 kg, with with attack hose of length not less than 5 m. -1 PCs.
12- Portable floodlight on support with a capacity of not less than 1000 W, protection degree not lower than 1P65, GOST R MEK 60598-1-2003
13- Group LED flashlight GOST R 53270 with explosion-proof configuration with charger
14- Portable lighting system, the luminous flux at least 1200 lm
15- Fixed lighting mast with floodlights with a capacity of not less than 10 kW. Floodlights not less than 8 m high. КFloodlights with protection degree not lower than IP45 GOST 14254, with remote control
16- Rod grounding switch GOST 16556.
17- Portable grounding for firefighting vehicles, the of grounding wire cross-section diameter at least 16 mmg, length not less than 20 m with a case.
18- Insulating mat no smaller than 750x750 mm GOST 4997-75, thickness not less than 5-7 mm.
19- Latex insulating gloves (seamless) GOST 12.4.103-83, protection against DC and AC electric shock at voltage up to 1000 V, and additional tool at voltage above 1000 V in the temperature range from -40° c to +30° c
20- Rubber insulating boots GOST 13385-78. Protection against electric current voltage up to 1000 V. Temperature range of at least-30° C to +50° C.
21- Insinuating scissors are designed for cutting cables and wires in electrical systems with voltage up to 1000 V AC and 1500 V DC. Diameter of wires made from aluminium, copper not less than 10 mm, of steel of not less than 5 mm. GOST 11516-94. Temperature range at least from -30° С up to + 70DC. dimensions (length/width/height): 550x300x70 mm.
22- Wire clamp
23- Screwdriver-indicator GOST R 52319-2005.
24- Breathing apparatus Drager sPSS 3000 with rescue tools, a cylinder of composite metal VMK 6.8 -139 -300 (with protective cover) and 4 ( four) facial masks (a mask with tapes for fastening on the head with a neck strap and a storage pouch), set.
25- Cylinder of composite metal VMK 6.8 -139 -300 for breathing apparatus (backup)
26- Equipment for breathing apparatus maintenance "SKAD-1 "
27- Sensor (alarm) of gas smoke rescuer stil position Drager Bodyquard
28- Insulating self-rescuer with compressed air GOST R 53259-2009, time of protective action of not less than 50 m, working pressure not exceeding 29.4 MPa (300kgf/cm2), weight not exceeding 5 kg.
29- Universal gas analyzer for toxic gases detection (CO, 02, CH4h H2S), operating temperature not less than -306 Sn <+50 ° c
30- PASS guiding line GDZS NST A-100 (or analogue). Two modes of operation (continuous glow, flashing mode), complete with two removable coils glowing wires of not less than 50 m and 100 m length, glowing wires not more than 5 mm diameter , degree of protection not lower than IP 66
31- Heat reflective suit GOST R 53264 ( TC-800)
32- Chemical protection suit GOST R 53264, GOST R 12.4.259 53264 (type "Trelakem-Suler" (TE) * closed type).
33- Chemical protection suit GOST R, GOST R 12.4.259 53264 (type "Trelpkem-Super" (T)-open type).
34- Goggles of universal application, optical class # 1 (no distortion, has no restrictions on time of wearing), should provide 100% protection from UV rays GOST R 12.4.230.1-2007
35- Table (folding, portable) for breathing apparatus inspection and maintenance with dimensions of not less than 900 × 600 mm.
36- Vehicle radio station Motorola GM 140 (with 25-40 W (or analogue)output power 403 – 470 MHz range with voltage converter 24/12V, 15А
37- Portable radio Motorola GP140U (or analogue), 403-470 MHz frequency range, with headset, charger, and backup battery
38- Signal loudspeaker unit with flashing loud-speaking regime GOST R 50574-2002, power not less than 120 W dimensions (length/width/height) not more 1050/280/150 mm.
39- Electric megaphone, with a portable microphone. Maximum power output of not less than 35 W, coverage at least 500 m
40- Fire rescue line GOST R 53266-2009 of length not less than 30 m, in a case.
41- Fire rescue line GOST R 53266-2009, of length not less than 50 m in a case.
42- High-rise (climbing) equipment KSV-50.
43- Portable ventilator GS-10 (or equivalent), together with Backup oxygen сylinder
44- Bag valve mask reusable.
45- First aid kit for fire-fighting vehicles {Medical kit NIENP-01), according to the order of the Ministry of Health of the Russian Federation No. 408 of 10.10.2012
46- Scoop stretcher(orthopedic) telescopic,height adjustable of length not less than 2140 mm, width not less than 490 mm, height not less than 70 mm.
47- Soft frameless stretcher. Inclided: Waterproof stretcher, a case. Dimensions when unfolded: not less than 2000x850 mm, dimensions in a case (length/width/height) not less than 310/50/510 mm, weight not more than 2 kg, nominal load: not less than 150 kg
48- Splints to immobilize the upper limbs
49- Splints to immobilize the lower limbs
50- All-metal hook GOST R 50982-2009
51- Light pry bar GOST R 50982-2009
52- Heavy pry bar GOST r 50982-2009
53- Axe GOST R 50982-2009
54- Rescue tools GOST R 50982-2009
55- Axe GOST 18578-89
56- Seat belts cutter
57- Forging hammer of weight no less than 5 kg GOST R 50982-2009
58- Electric chain saw, with two spare chains
59- Electric drill(electric air hammer), impact force at least 63 J., power not less than 2 kW. For concrete and brick structures demolition.
60- Oxygen petrol cutting torch, tank capacity not less than 93.6 cm3, power not less than 4.5 kW, wheel diameter 350 mm/14 inch maximum cutting depth not less than 125 mm/5 inch, with five disks.
61- Magnetic accessory set for leaks (magnetic console KM-450, magnetic accessory (console) K-500, magnetic snap (console) K-200/80-100).
62- Chassis spare wheel
63- Breakdown triangle GOST R 41.27 -2001
64- First aid kit
65- Tools and accessories as per chassis manufacturer's schedule (including pump and tire pressure controller)
66- Hydraulic jack GOST R 53822-2010 with load capacity at least 10 t.
67- Bench tool set for vehicle repairing, in a 5-section box.
68- Blow torch GOST 12.2.008-75
69- Portable carbon dioxide fire extinguisher OU-5 GOST p 51057-2001.
70- Portable fire extinguisher OP-5 GOST p 51057-2001.
71- Traffic cone of PVC with at least 320 mm high with a reflective tape.
72- Tape to safeguard the emergency site of length not less than 500 m, red-and-white colour.
73- Polyethylene csnister for water, with 5 l capacity GOST r 51760-2001.
74- Canister for the fuel with 20 l capacity GOST 5105-82.

Equipment: 
Fixed generator 1 1
Portable generator 2 1
6.5 l. Handheld starter 3 1
Portable reel with cable 4 1
Portable reel with cable 5 2
Switchboard 6 1
Protective cutout device 7 1
Electric branch box 8 3
Adapter 9 3
Induced-draft fan 10 1
Induced-draft fan 11 1
Portable floodlight 12 2
LED electric torch 13 4
Lighting system 14 1
Lighting mast 15 1
Rod grounding switch 16 1
Portable grounding 17 2
Insulating mat 18 2
Insulating gloves 19 2
Insulating boots 20 2
Insinuating scissors 21 2
Wire clamp 22 1
Screwdriver 23 1
Breathing apparatus 24 9
Backup cylinder 25 9
Set of equipment 26 1
Gas and smoke rescuer detector 27 6
Self-rescuer 28 6
Gas analyzer 29 1
Guiding line 30 2
Heat-reflecting suit 31 4
Chemical protection suit 32 6
Chemical protection suit 33 6
Protective googles 34 2
Folding table 35 1
Radio 36 1
Portable radio station 37 5
Signal loudspeaker unit 38 1
Electric megaphone 39 1
Rope 40 2
Rope 41 2
Climbing equipment 42 2
Portable ventilator GS-10 43 1
Bag valve mask 44 1
First Aid Kit 45 1
Scoop stretcher 46 1
Frameless stretcher 47 1
Splints set 48 1
Splints set 49 1
Hook 50 1
Light pry bar 51 1
Heavy pry bar 52 1
Fire axe 53 1
Rescue tools 54 1
Axe 55 1
Knife (cutter) 56 1
Forging hammer 57 1
Round-pointed spade 1
Square-faced shovel 1
Chain saw 58 1
Electric perforator 59 1
Oxygen petrol cutting torch 60 1
Magnetic accessory set 61 1
Spare wheel 62 1
Towing line 1
Breakdown triangle 63 1
First aid kit 64 1
Vehicle blocking chock 2
Tools 65 1
Jack 66 1
Tool kit 67 1
Blow torch 68 1
Carbon dioxide fire extinguisher 69 1
Fire extinguisher 70 1
Traffic cone 71 4
Barrier tape 72 1
Water canister with 5-litre capacity 73 1
Fuel canister with 20-litre capacity 74 1
Description
The advantages of this model: 
  • It can operateat a temperature from minus 40 to plus 40° c,  at an atmosphere of  1 and 2 types as per GOST 15150
  • The engine and transmission provide allow the vehicle to work in a nominal a mode during 6:00
  • Te rollover threshold with a total mass in full operational availability is at least 30 degrees
  • Angle of approach: Front-20"; Rear -15"
  • Pneumatic dual circuit braking system with a division of the contours into the front axle and rear truck, with anti-lock braking system
  • The batteries are protected from dirt and moisture
  • The fuel tank capacity allows operating for 6 hours from primary power source at nominal load without refuelling
  • The exhaust system is equipped with a spark arrestor
  • There is an additional fuel filter with a water separator
  • The driver's cabin and the crew cabin represent common space, constitute a single sealed structure
  • The cabin design saves space if the car is overturned, or in case of head-on collision, rear-end accidents and sideways.
  • The equipment in the cabin is positioned in such a way that there are no sharp corners and edges
  • The design of the mast allows its operation without stretching at wind speed up to 10 mps.
  • The mast is equipped with a mechanism of orientation (rotary device), spotlights  with remote drive in two planes
  • A high-resolution video registrator  (Full HD)  1280 * 720, 30 fps is available, viewing angle width of 110 degrees, no pauses between blocks, sound recording available;
  • Sensor pixel count- 2 MP
Description: 

The cabin is a basic cabin of the chassis, salon type, 2-door, 2- seat (or with a separate cabin 4-door 7-seat).In the doorway of the cabin and in the door openings there are handrails for convenience and rapid entrancw of the crew. In the second row of the cabin there are 4 seats with individual backs. A breathing apparatus with compressed air can be located nearby. Each seat has a separate mechanism for fixation of the respiratory apparatus, and under the seats there are places for fire-fighting equipment. The common space for fie fighters makes team work more coordinated and rapid. The cabin is equipped with handrails, indoor lighting, heating, a manhole on the top and specific control panels and control systems for the vehicle and its equipment. There are fixed automatic bottom steps which allow the crew to enter the cabin easily.

The bodywork and the cabin are an assembled structure made of aluminium profiles, lined with aluminium sheets in accordance with adhesion technology.( reinforced fibreglass sheets are also possible). The bodywork forms a part of the fire superstructure and serves for placement and protection of firefighting equipment and emergency resue tools from damage during transportation. Our own sandwich-panels are used for increased heat and noise insulation, as well as for increased comfort.

The bodywork consists of the compartments for firefighting equipment and emergency resue tools.

The bodywork fixation to the vehicle frame is based on elastic damping elements that decrease the bodywork stress caused by the frame torsion.

The compartments are equipped with roller-shutters (panel doors are also possible). The shutters are made of aluminium alloys.

All doors are equipped with self-locks, which retain them in a closed position, also there is an open doors indication on the control panel in the driver's cabin.

Open doors, manholes, and other structural elements of the vehicle, which increase its overall dimensions, are equipped with reflective elements and other signalling devices indicating the dimensions of the vehicle when the doors are open during its stop.

The firefighting equipment is located considering the tactics of its usage, which ensures the reliability of fixation, accessibility, convenience and safety during its mounting and demounting.

The firefighting equipment when located is united into groups according to its purpose(as standard):

- personal firefighter equipment and personal reapiratory protection equipment;

- equipment for smoke exhaustung;

- structure cutting and demolition equipment;

- power tools, hydro tools, etc.;

- other equipment.

The firefighting equipment is securely installed and mounted in the compartments of the firefighting vehicle.

Stairs for climbing the vehicle top are made of an aluminum alloy.

There are folding bottom steps for the convenience of the crew.

Energy-efficient LED technology is used.

To register a detailed proposal with options please send us a request or contact our company via contact phone numbers.

Gallery

Induced-draft fan of increased capacity 40 000 m3

Induced-draft fan of increased capacity 15 000 m3

Lighting mast height of 8 m, with a capacity of 10 kW

Fixed generator 26 kW

Equipment for external input

Request a call